Zoriver大内孔法兰连接液位变送器YS1PF

适用于浆状,颗粒,粘稠介质

法兰式液位变送器YS1PF
YS-1HF Flange Liquid Level Transmitter

   一、概述General Remark：
    该型号为 YS-1 的变形产品，其显著特点是采用较大内孔和法兰连接方式，适用于非密闭场合，尤其是粘稠、或浆状介质或富含颗粒类介质的测量。采用此种形式可达到不易堵塞，便于清洗的效果，进一步发挥了陶瓷电容传感器抗腐蚀性能好的技术特点和较经济的优势。可广泛用于石油、化工、电力、冶金、制药、食品等许多工业领域。
    This model is derived from YS-1, it features big internal hole and flange connection, suitable for non sealed application, especially for viscous, slurry media or granule media. This design eliminates the risk of blocking, and provides easy cleaning, further develops ceramic capacitance sensor’s function of corrosion-proof and economic advantage. It finds many utilities in petroleum, chemical, power,
metallurgy, pharmaceutical, food industries.

    二、特点Characteristic
    ● 精度高，稳定性好。
       high accuracy, good stability

    ● 二线制工作方式，4～20mA 信号输出。
       2 line working mode, 4～20mA signal output
    ● 敏感部件及线路板是全固体结构，坚固抗振。
       sensitive component and circuit board are in solid construction, rigid vibration-proof
    ● 抗干扰能力强，温度稳定性好;
       excellent interference-proof, good thermal drift;
    ● 防爆壳体结构，可全天候使用。
       explosion-proof enclosure structure, weather-proof
    ● 具有最优良的防腐性能，保证最好的防腐性价比。
       most outstanding corrosion-proof, ensure best utility reliability

    ● 结构轻巧，简单合理，无须支架，无须水平安装，可直接任意位置安装管道上。
       light construction, simple reasonable, no bracket required, no horizontal mounting required, available mounting at any position on pipeline.

   三、工作原理Working Principle

     变送器由传感器与电子元件线路组成，被测介质的压力直接作用于传感器的陶瓷膜片上，使膜片产生与介质压力成正比的微小位移，正常工作状态下，膜片最大位移不大于0.025mm，电子线路检测这一位移量后，即把这一位移量转换成对应于这一压力的标准工业测量信号（4~20）mA。超压时膜片直接贴到坚固的陶瓷基体上，由于膜片与基体的间隙只有0.1mm，过载时膜片的最大位移只能是0.1mm，所以从结构上保证了膜片不会产生过大变形。由于膜片采用高性能的工业陶瓷，因而使传感器具有很强的抗冲击及抗过载能力。
    Transmitter is composed of sensor and electronic element circuit, pressure of measured medium directly applies on sensor s ceramic diaphragm, force diaphragm to displace tinily in proportion to pressure of medium, under normal working condition, diaphragm displace no more than 0.025mm, electronic circuit detects this displacement, and convert it into standard industrial measuring signal i.e. (4～20mA) corresponding to this pressure. When overpressure, diaphragm directly stick to solid ceramic base body, as there is only 0.1mm gap between diaphragm and base body, when overpressure, the maximum diaphragm displacement could be no more than 0.1mm, (at that time, measuring diaphragm sticks to ceramic bracket, avoid damage) so structurally prevent diaphragm from excessive deformation. Because diaphragm adopts high functional industrial ceramic, sensor is significantly shock-proof and overload-proof.

                       图-1 YS1PF 系列陶瓷电容压力变送器原理图
    Figure - 1 YS-1 Series Ceramic Capacitance Pressure Transmitter Principle Scheme

   四、主要技术指标Main Technical Index

   技术指标Technical Index
    使用对象液体、气体或奖状介质
    Utility Object: Liquid, gas or slurry media
    测量范围表压：0～10Kpa～7Mpa;负压：-100KPa～7MPa
    Measuring range: Gauge pressure：0～10Kpa～7Mpa;Minus pressure：-100KPa～7MPa
    输 出4～20mADC
    Minus pressure：-100KPa～7MPa

    电 源13～30VDC
    Power Supply: 13～30VDC

    负载特性4～20mADC 二线制负载R ≤ 50(V-13) （见图-2）
    Load characteristic: 4～20mADC 2 line load R ≤ 50(V-13) （see figure -2）

    温度范围环境温度： -20～+70℃ ;
    Temperature limit: Ambient temperature： -20～+70℃ ;
    存储温度：-20～+80℃
    storage temperature：-20～+80℃
    标准介质温度： -20～+80℃（短时可达130℃）
    Standard medium temperature： -20～+80℃（short time up to 130℃）
    外壳防护优于IP65
    Enclosure protection: Better than IP65
    防爆类型本安型ia Ⅱ CT5 应外配安全栅
    Explosion-proof mark: Intrinsically safety type ia Ⅱ CT5 should have extra safety barrier

                   负载特性（图-2）Load Characteristic（figure-2）

                     (Transmitter s load characteristic diagram)

    性能指标Functional index
    综合精度标准提供0.25%，最高精度可达± 0.1%BFSL
    General accuracy: Supply standard ± 0.25%BFSL/year，

        maximum accuracy ± 0.1% BFSL/year
    稳定性优于± 0.1%BFSL/ 年
    stability: Better than ± 0.1% BFSL/year
    温度影响在-20～+70℃范围内，变化量小于± 0.18% / 10℃
    thermal effect: within-20～+70℃，variation below ± 0.18%/10℃
    振动影响在任何方向上振动频率为20-200Hz 时，变化量小于± 0.02% BFSL
    vibration effect: In any direction, vibration frequency 20-200Hz，

        variation below ± 0.02% BFSL/year
    冲击影响任何方向100G 冲击11ms 后，变化量小于± 0.02% BFSL
    impact effect: In any direction 100G impact after 11ms,

        variation below ± 0.02% BFSL

    负载影响只要输入变送器的端子电压高于12V，就无负载影响。
    load effect: No load effect as long as voltage input to transmitter’s terminal greater than 12V

    位置影响无

    position effect: none

    结构指标Structural Index
    结构材料constructional material:

        膜片：氧化铝陶瓷 外壳：低铜铸铝
       diaphragm：aluminium oxide ceramic

            Enclosure material：low copper cast aluminum

        接触介质材料：SUS304
        wetted material：SUS304
       “O”型圈密封结构：丁腈橡胶、聚四氟乙烯或氟橡胶
       “ O”type ring：buna N , PTFE OR fluoroelastomer

       过程连接法兰连接Flanged connection
       电气连接process connection:

       可根据需要从任何一个出口引出，建议使用φ 10 工业电缆作为引线，以便密封。引出接头可选用通用电缆接头PG16 或M20 × 1.5，不引线一端用端盖封住。

       electric connection: On request lead from any exit, suggest φ 10 industrial cable as lead, so that it is sealed.Leadout socket could be general cable socket PG16 or M20 × 1.5，use end cap to seal no lead end.

    五、 结构及安装方式construction and mounting options

                           图-3 是法兰液位变送器的结构示意图
          figure-3 is flange liquid level transmitter s constructional scheme

                  图-4 是法兰的结构示意图及尺寸表 单位（mm）
     Figure-4 is flange construction scheme and dimension chart unit（mm）

    1. 直接安装在测量点上（任意角度）。
       directly mount on measuring point（any angle）

    2. 尽量安装在温度梯度与温度波动小的测压点上，同时避免强振动和冲击。
       suggest mount on measuring point with lower temperature gradient and temperature fluctuation, meanwhile avoid vibration and impact.
    3. 室外安装时，尽可能放置于保护盒内，避免阳光直射和雨淋，以保持变送器性能稳定和延长使用寿命。
       in case of outdoor mounting, preferred mounting in protection case, avoid direct exposure to sunlight and rainfall, to maintain transmitter s functional stability and longer service life.
    4. 测量蒸汽或其它高温介质时，注意不要使变送器的工作温度超限。必要时请安装散热器或其它冷却装置连接。
       when measuring steam or other high temperature media, make sure transmitter s working temperature limit is observed. Fit cooler or other cooling device if necessary.
    5. 安装时应在变送器和介质之间加装压力截止阀，以便检修和防止取压口堵塞而影响测量精度。在压力波动范围大的场合还应加装阻尼器或压力缓冲装置。
    when mounting, shut valve should be used between transmitter and medium, for easy maintenance and to prevent pressure taking port from blocking that influences measuring accuracy. Damper or pressure buffer should be used where big pressure fluctuation exists.
    注：不得随意更换或改动可能影响防爆性能的元器件或结构。
    Note：random replacing or altering elements or construction that may impair explosion-proof function is prohibited.

   六、系统连接及调试System connection and adjustment
    变送器在测量系统中的连接见图4。建议电源电压Us 选用24V.DC。
    Connection of pressure transmitter in measuring system refers to figure 4. Suggest power supply Us uses 24V.DC
    二次仪表中采样电阻（负载电阻）RL 的阻值选用250 Ω。如果Us 和RL 选用别的数值，那么RL 值不能超过由公式计算得到的数值。电源通过信号线接到变送器， 变送器顶部两侧面的连接孔用电缆密封或信号线装配，信号电缆通过紧固螺母锁紧，不使用的连接口必须密封。
    Sampling resistance in secondary instrument（load resistance）RL uses 250Ω。If resistance deviates for Us and RL, RL value shall not exceed the value from formula RL = Power supply is connected to transmitter via signal cable, connections holes at both sides of top of transmitter is sealed with cable or assembled with signal cable, signal cable is fastened by lock nuts, idle connection hole must be sealed.
    A：测量系统接线图measuring system wiring scheme
    在系统回路中必须采用屏蔽信号电缆，并可靠接地。
    Shielded signal cable must be used in system loop, and must be grounded firmly.

                           图-4 测量系统示意图（4～20mA）
                   figure-4 measuring system scheme（4～20mA）

    B：本安型压力变送器intrinsically safety type pressure transmitter
    YS-1-B本安型压力变送器采用本质安全电路，适用于爆炸危险区域，防爆等级ExiaIICT5(防爆合格证编号：CE042114)，技术性能指标与普通型压力变送器相同。在系统回路中必须采用屏蔽信号电缆，并可靠接地。
    YS-1-B intrinsically safety type pressure transmitter adopts intrinsically safety circuit, suitable for explosive hazardous zone, explosion-proof class ExiaIICT5(explosion-proof certificate no.：CE042114)，echnical function index is same as standard pressure transmitter. Shielded signal cable must be used in system loop, and must be grounded firmly.

                            图-5 本安型测量系统示意图（4～20mA）
              figure-5 intrinsically safety measuring system scheme（4～20mA）

    变送器出厂前已根据用户需求，量程、精度均已调到最佳状况，一般不需校验。但以下情况需重新校验：
    before delivery transmitter has been set range, accuracy within accuracy range as per customer s request, normally doesn t need calibration but as a exception if following situations occur：

    A. 运输途中出现跌落、强烈震颠和碰撞；
       falling down, strong shock and vibration in transit；
    B. 存放期超过一年；
       over 1 year storage；

    C. 长时间运行后，出现大于精度范围内的误差；
       long time operation, error occurs greater than accuracy range;
    D. 使用单位的例行检验；
       user s routine inspection；

    YS1PF选型表 HOW TO ORDER
    型号代码特性说明Code Introduction
    基本型号Basic type
        YS1PF = 法兰式液位变送器  Flange Liquid Level Transmitter
    输出Signal output
        420    = 24V，4~20mA
        015    = 24V，1~5V
    精 度Accuracy
        025    = 0.25 级 ± 0.25%
        050    = 0.5 级 ± 0.5%
    测 量 范 围Ranges
        M120 = 1 MPa
        在 10 kPa -7 MPa 之间选项

        具体代码请参看量程对照表

    仪表连接Connection
        根据客户提供的法兰连接标准

欢迎来电咨询订购Zoriver大内孔法兰连接液位变送器YS1PF适用于浆状,颗粒,粘稠介质

电话: 56291930

传真：

QQ：823377546 36968574